AC servo motor
Bosch Rexroth MS2E ATEX servo motors
Explosion-protected synchronous servo motors for ATEX zone 2 (gas) and zone 22 (dust), in six sizes with maximum torque up to 266 Nm and self-cooled standstill torque up to 64 Nm.
Need this part, a replacement or a better-fit option? Our engineers help with selection, procurement, sourcing, competitive pricing and lead times.
Engineering support · Product sourcing · Procurement
Get pricing or a checked replacement
Need Bosch Rexroth parts, a replacement or another suitable option? Send your part number or describe the application. We’ll review the requirement and help with product selection, sourcing, pricing and lead times.
- Exact parts and engineer-checked alternatives
- Manufacturer-direct options where available
- Standard, modified and custom solutions
No obligation to buy. Have a datasheet, drawing or nameplate photo? Reply to your confirmation email to attach it.
Need help choosing? Build a specification →Need help choosing? Open the specification builder
Spec builder
Specify what you need instead of MS2E ATEX servo motors
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Key specifications
| Peak torque (max) | 266 Nm |
|---|---|
| Standstill torque (max) | 64 Nm |
| Frame sizes | 58, 82, 98, 116, 140, 196 (flange) |
| Feedback | SIL2 PL d encoder |
| Certification | ATEX zone 2 / zone 22, device group II, category 3 |
| Connection | single-cable up to MS2E07 |
Summarised in our own words from Robert Bosch GmbH's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Standstill torque M0 at 60 K, self-cooled.
Specify Motion is not affiliated with Robert Bosch GmbH. Bosch Rexroth and MS2E ATEX servo motors are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Bosch Rexroth MS2E ATEX servo motors replacement and alternative options
Use these supply-network options as a starting point for an engineering check. We can also help source the original Bosch Rexroth part. Published series figures do not establish an exact-model or drop-in replacement: confirm ratings, fit, interfaces and approvals for your application.
Leadshine's AC servo motors for the EL8/EL7/EL6 drives: ELM1 is the economy line and ELM2 the general-purpose line, both with 23-bit absolute encoders, IP65/IP67 sealing and up to 3.5x overload. The catalogue extends ELM2M to 22 kW and previews a 26-bit ELM3.
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
Typical applications
What an AC servo motor is
An AC servo motor is a permanent-magnet synchronous motor designed for closed-loop control of position, speed and torque. A wound stator is driven by a servo drive with sinusoidal three-phase current, while magnets on the rotor follow the rotating field. A high-resolution encoder or resolver on the shaft feeds position back to the drive, which adjusts current many thousands of times a second. The result is precise, dynamic motion with high peak torque, typically about three times the continuous rating for short periods.
When engineers choose an AC servo motor
Choose an AC servo for machine axes needing fast, accurate motion under varying loads, such as packaging, robotics, machine tools and printing. Compared with steppers, servos keep torque at high speed and cannot silently lose position. The trade-offs are cost and set-up: a servo needs a matched drive, feedback and tuning. For simple, low-speed indexing with a steady load, a stepper may be cheaper. For very low speeds and high torque, a gearbox or direct-drive motor may be needed.
How to specify the Bosch Rexroth MS2E ATEX servo motors
Send these with your enquiry and an engineer can confirm the right MS2E ATEX servo motors variant or an equivalent:
- Continuous and peak torque (Nm)
- Rated and maximum speed (rpm)
- Load inertia and inertia ratio
- Supply voltage: 230 V single-phase or 400 V three-phase
- Feedback: incremental or absolute encoder, resolution (bits)
- Holding brake, IP code and shaft options
- Flange size and mounting (mm)
Common mistakes to avoid
- Sizing on peak torque without checking RMS torque over the cycle
- Ignoring load-to-motor inertia ratio, which makes tuning hard
- Forgetting the brake is for holding, not dynamic stopping
- Using a motor and drive pair that the supplier has not matched
Bosch Rexroth MS2E ATEX servo motors: frequently asked questions
Can you help replace Bosch Rexroth MS2E ATEX servo motors or source the original?
Send the full model code, quantity and required date. Our engineers can check original-part availability and assess suitable alternatives, including Motion Control Products options where appropriate. We confirm compatibility and any changes needed before recommending a replacement.
What is the Bosch Rexroth MS2E ATEX servo motors?
Explosion-protected synchronous servo motors for ATEX zone 2 (gas) and zone 22 (dust), in six sizes with maximum torque up to 266 Nm and self-cooled standstill torque up to 64 Nm. Published series figures include peak torque 266 Nm, standstill torque 64 Nm. It is made by Robert Bosch GmbH; Specify Motion can help source it or propose an equivalent.
Who makes the Bosch Rexroth MS2E ATEX servo motors?
The Bosch Rexroth MS2E ATEX servo motors is made by Bosch Rexroth (Robert Bosch GmbH) and is listed here for engineers comparing options. Specify Motion is not affiliated with Robert Bosch GmbH; brand names are used only to identify the product.
What is the peak torque of the Bosch Rexroth MS2E ATEX servo motors?
The published series maximum peak torque is 266 Nm. Individual models and sizes in the MS2E ATEX servo motors range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Bosch Rexroth MS2E ATEX servo motors?
We can assess suitable replacement options. On published figures, Leadshine ELM1 / ELM2 AC Servo Motors is options to assess from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the inertia ratio in servo sizing?
The inertia ratio compares the load inertia reflected to the motor shaft with the motor's rotor inertia. High ratios make the axis harder to tune and slower to settle. Many engineers aim for below about 10:1, and lower for highly dynamic axes, using a gearbox to reduce reflected inertia where needed.
Do AC servo motors need an absolute encoder?
Not always. Incremental encoders need a homing routine after power-up, which is acceptable on many machines. Absolute encoders know their position at power-on, avoiding homing, which saves time and suits robots and multi-axis machines. Multi-turn absolute encoders track turns even when power is off.
Further reading: How to select a servo motor · Servo vs stepper · Servo and stepper motors
Other ac servo motor series
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Bosch Rexroth MS2E ATEX servo motors: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.