Hybrid stepper motor
Lin Engineering X8718 series (NEMA 34) hybrid stepper motor
High-torque NEMA 34 1.8° hybrid stepper with 4.8 to 15.0 Nm (679.7 to 2,124.2 oz-in) holding torque; the 11018 NEMA 42 range extends to 32 Nm.
Need this part, a replacement or a better-fit option? Our engineers help with selection, procurement, sourcing, competitive pricing and lead times.
Engineering support · Product sourcing · Procurement
Get pricing or a checked replacement
Need Lin Engineering parts, a replacement or another suitable option? Send your part number or describe the application. We’ll review the requirement and help with product selection, sourcing, pricing and lead times.
- Exact parts and engineer-checked alternatives
- Manufacturer-direct options where available
- Standard, modified and custom solutions
No obligation to buy. Have a datasheet, drawing or nameplate photo? Reply to your confirmation email to attach it.
Need help choosing? Build a specification →Need help choosing? Open the specification builder
Spec builder
Specify what you need instead of X8718 series (NEMA 34)
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Key specifications
| Holding torque | 4.8–15 Nm |
|---|---|
| NEMA sizes | 34 |
| Step angle | 1.8 ° |
Summarised in our own words from Lin Engineering's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Holding torque converted from oz-in. 11018 (NEMA 42): 1,727.67 to 4,531.58 oz-in.
Specify Motion is not affiliated with Lin Engineering. Lin Engineering and X8718 series (NEMA 34) are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Lin Engineering X8718 series (NEMA 34) replacement and alternative options
Use these supply-network options as a starting point for an engineering check. We can also help source the original Lin Engineering part. Published series figures do not establish an exact-model or drop-in replacement: confirm ratings, fit, interfaces and approvals for your application.
110 mm 2-phase hybrid stepper, 11-33 Nm, for high-torque industrial and CNC axes; pairs with high-voltage AC stepper drives.
| Published maximum | X8718 series (NEMA 34) | NEMA 42 High Torque (M110STH) |
|---|---|---|
| Holding torque | 15 Nm | 33 Nm meets or exceeds |
| Current | — | 8 A |
Leadshine's current 2-phase open-loop hybrid stepper range from 20 mm to 130 mm frames, with encoder, brake, IP65 and gearbox variants.
| Published maximum | X8718 series (NEMA 34) | Leadshine CM Series (2-phase) |
|---|---|---|
| Holding torque | 15 Nm | 45 Nm meets or exceeds |
| Current | — | 7 A |
3-phase high-voltage closed-loop steppers in NEMA 34/42 (catalogue also lists 17/23) for 220 VAC ES2 drives, 8-20 Nm.
| Published maximum | X8718 series (NEMA 34) | Leadshine ES2-MH Series (3-phase high … |
|---|---|---|
| Holding torque | 15 Nm | 20 Nm meets or exceeds |
| Current | — | 6 A |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
Typical applications
What a hybrid stepper motor is
A hybrid stepper motor moves in fixed angular steps, typically 1.8° or 200 full steps per revolution, as a drive switches current through its windings in sequence. It combines a permanent-magnet rotor with toothed iron stator and rotor sections, giving high holding torque and fine resolution. With a microstepping drive, each full step is split into smaller steps for smoother motion. Steppers usually run open loop, so position is known by counting steps rather than measured.
When engineers choose a hybrid stepper motor
Choose a hybrid stepper for low-cost, simple positioning at low to moderate speed, such as indexing, dosing, small axes and instruments. It holds position strongly at standstill and needs no tuning. The trade-offs are falling torque at speed, resonance and possible lost steps if overloaded. Where speed is high, loads vary or a missed position would cause a fault, a closed-loop stepper or servo is safer.
How to specify the Lin Engineering X8718 series (NEMA 34)
Send these with your enquiry and an engineer can confirm the right X8718 series (NEMA 34) variant or an equivalent:
- Holding torque (Nm)
- Torque needed at operating speed (Nm at rpm)
- Frame size (NEMA or mm)
- Step angle (°)
- Phase current and inductance (A, mH)
- Drive voltage (V)
- Shaft, encoder and IP options
Common mistakes to avoid
- Sizing on holding torque instead of the pull-out curve
- Driving with too low a supply voltage, losing high-speed torque
- Leaving out torque margin, typically 30% to 50%
- Ignoring resonance in the mid-speed range
Lin Engineering X8718 series (NEMA 34): frequently asked questions
Can you help replace Lin Engineering X8718 series (NEMA 34) or source the original?
Send the full model code, quantity and required date. Our engineers can check original-part availability and assess suitable alternatives, including Motion Control Products options where appropriate. We confirm compatibility and any changes needed before recommending a replacement.
What is the Lin Engineering X8718 series (NEMA 34)?
High-torque NEMA 34 1.8° hybrid stepper with 4.8 to 15.0 Nm (679.7 to 2,124.2 oz-in) holding torque; the 11018 NEMA 42 range extends to 32 Nm. Published series figures include holding torque 4.8 Nm, holding torque 15 Nm, step angle 1.8 °. It is made by Lin Engineering; Specify Motion can help source it or propose an equivalent.
Who makes the Lin Engineering X8718 series (NEMA 34)?
The Lin Engineering X8718 series (NEMA 34) is made by Lin Engineering and is listed here for engineers comparing options. Specify Motion is not affiliated with Lin Engineering; brand names are used only to identify the product.
What is the holding torque of the Lin Engineering X8718 series (NEMA 34)?
The published series minimum holding torque is 4.8 Nm. Individual models and sizes in the X8718 series (NEMA 34) range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Lin Engineering X8718 series (NEMA 34)?
We can assess suitable replacement options. On published figures, Motion Control Products NEMA 42 High Torque (M110STH) and Leadshine CM Series (2-phase) are options to assess from our supply network. An engineer confirms the fit against your application before recommending anything.
Why do stepper motors lose torque at high speed?
Winding inductance limits how fast current can rise each step. As speed increases there is less time per step, so current and torque fall. A higher drive voltage raises current faster and extends the torque curve. Always size from the pull-out torque curve at your drive voltage.
Does microstepping increase accuracy?
Microstepping makes motion smoother and gives finer resolution, but accuracy is not improved in proportion. Each microstep produces only a small torque increment, so load torque can shift the actual position. Accuracy is mostly set by the motor's step accuracy and the load.
Further reading: How to select a stepper motor · Servo vs stepper · Servo and stepper motors
Other hybrid stepper motor series
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Lin Engineering X8718 series (NEMA 34): the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.