Rod actuator
Oriental Motor EAC Series electric linear cylinders (AZ) rod actuator
Ball-screw electric cylinders driven by AZ Series closed-loop steppers in 42 mm and 60 mm frames, strokes of 50 to 300 mm, push force up to 500 N and repeatability of +/-0.02 mm.
Need this part, a replacement or a better-fit option? Our engineers help with selection, procurement, sourcing, competitive pricing and lead times.
Engineering support · Product sourcing · Procurement
Get pricing or a checked replacement
Need Oriental Motor parts, a replacement or another suitable option? Send your part number or describe the application. We’ll review the requirement and help with product selection, sourcing, pricing and lead times.
- Exact parts and engineer-checked alternatives
- Manufacturer-direct options where available
- Standard, modified and custom solutions
No obligation to buy. Have a datasheet, drawing or nameplate photo? Reply to your confirmation email to attach it.
Need help choosing? Build a specification →Need help choosing? Open the specification builder
Spec builder
Specify what you need instead of EAC Series electric linear cylinders (AZ)
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Key specifications
| Force (max) | 500 N |
|---|---|
| Stroke (max) | 300 mm |
| Screw lead | 6 or 12 |
| Screw type | ball screw |
| Repeatability | 0.02 mm |
| Frame sizes | 42 (EAC4), 60 (EAC6) |
| Thrust | ~70-400 N transport thrust; 100-500 N push force, by frame and lead |
Summarised in our own words from ORIENTAL MOTOR CO., LTD.'s published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Max speed and IP not stated on the page read. Guided versions available.
Specify Motion is not affiliated with ORIENTAL MOTOR CO., LTD.. Oriental Motor and EAC Series electric linear cylinders (AZ) are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Oriental Motor EAC Series electric linear cylinders (AZ) replacement and alternative options
Use these supply-network options as a starting point for an engineering check. We can also help source the original Oriental Motor part. Published series figures do not establish an exact-model or drop-in replacement: confirm ratings, fit, interfaces and approvals for your application.
Ball-screw servo electric cylinder in seven frame sizes from 32 to 150, with inline or reverse-parallel motor mounting and optional force sensing, aimed at hydraulic and pneumatic replacement.
| Published maximum | EAC Series electric linear cylinders (AZ) | SRB Linear Servo Actuator |
|---|---|---|
| Force | 500 N | 49,033 N meets or exceeds |
| Stroke | 300 mm | 1,000 mm meets or exceeds |
| Speed | — | 1,250 mm/s |
Economical stainless-tube electric rod actuator in sizes 10, 15 and 20, aimed at replacing pneumatic cylinders for gating, sorting and diverting; SS1/SS2 options give an all-stainless, IP69K washdown build.
| Published maximum | EAC Series electric linear cylinders (AZ) | ERD (incl. ERD-SS1 / ERD-SS2 stainless… |
|---|---|---|
| Force | 500 N | 2,224 N meets or exceeds |
| Stroke | 300 mm | 610 mm meets or exceeds |
| Speed | — | 1,016 mm/s |
RSA-based rod actuator with integral hardened guide rods, bearings and a tooling plate, so it can carry side and offset loads without external guidance.
| Published maximum | EAC Series electric linear cylinders (AZ) | GSA Guided Screw Actuator |
|---|---|---|
| Force | 500 N | 4,226 N meets or exceeds |
| Stroke | 300 mm | 914 mm meets or exceeds |
| Speed | — | 3,124 mm/s |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
Typical applications
What a rod actuator is
A rod actuator, sometimes called an electric cylinder, converts motor rotation into linear thrust through a screw and nut inside a tube, pushing a rod in and out like a pneumatic or hydraulic cylinder. The screw is usually a ball screw for efficiency, a roller screw for heavy loads or a lead screw for low cost. The rod is guided by bearings in the tube and an anti-rotation feature, and the motor is mounted inline or folded alongside through a belt or gear stage.
When engineers choose a rod actuator
Choose a rod actuator when the load is guided externally and needs pushing or pulling with controlled force, speed and position, typically to replace a pneumatic or hydraulic cylinder. It brings programmable positions, force control and energy savings. The trade-offs are side load and cost: the rod is not meant to carry significant radial load, and peak force for its size is lower than hydraulics. If the load needs carrying and guiding along the stroke, a rodless actuator or stage is usually better.
How to specify the Oriental Motor EAC Series electric linear cylinders (AZ)
Send these with your enquiry and an engineer can confirm the right EAC Series electric linear cylinders (AZ) variant or an equivalent:
- Force: peak and continuous or RMS (N)
- Stroke (mm) and retracted length limits
- Speed and acceleration (mm/s, m/s²)
- Duty cycle or full motion profile
- Positioning repeatability (mm)
- Side load and mounting arrangement: trunnion, clevis or flange
- Motor and feedback preference, and environment (IP code, °C)
Common mistakes to avoid
- Sizing on peak force alone instead of RMS force over the cycle
- Rigidly mounting both ends so misalignment puts side load on the rod
- Ignoring critical speed and column buckling on long strokes
- Forgetting that a ball screw back-drives, so vertical loads need a brake
Oriental Motor EAC Series electric linear cylinders (AZ): frequently asked questions
Can you help replace Oriental Motor EAC Series electric linear cylinders (AZ) or source the original?
Send the full model code, quantity and required date. Our engineers can check original-part availability and assess suitable alternatives, including Motion Control Products options where appropriate. We confirm compatibility and any changes needed before recommending a replacement.
What is the Oriental Motor EAC Series electric linear cylinders (AZ)?
Ball-screw electric cylinders driven by AZ Series closed-loop steppers in 42 mm and 60 mm frames, strokes of 50 to 300 mm, push force up to 500 N and repeatability of +/-0.02 mm. Published series figures include force 500 N, stroke 300 mm, repeatability 0.02 mm. It is made by ORIENTAL MOTOR CO., LTD.; Specify Motion can help source it or propose an equivalent.
Who makes the Oriental Motor EAC Series electric linear cylinders (AZ)?
The Oriental Motor EAC Series electric linear cylinders (AZ) is made by Oriental Motor (ORIENTAL MOTOR CO., LTD.) and is listed here for engineers comparing options. Specify Motion is not affiliated with ORIENTAL MOTOR CO., LTD.; brand names are used only to identify the product.
What is the force of the Oriental Motor EAC Series electric linear cylinders (AZ)?
The published series maximum force is 500 N. Individual models and sizes in the EAC Series electric linear cylinders (AZ) range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Oriental Motor EAC Series electric linear cylinders (AZ)?
We can assess suitable replacement options. On published figures, Motion Control Products SRB Linear Servo Actuator and Tolomatic ERD (incl. ERD-SS1 / ERD-SS2 stainless options) are options to assess from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the difference between a rod actuator and a rodless actuator?
A rod actuator pushes and pulls a rod extending from its body, so it suits loads that are guided by the machine, much like a cylinder. A rodless actuator moves a carriage along the body and carries the load itself, which handles moment loads and long strokes within the actuator's own length. Pick rod for thrust and rodless for carrying.
Can an electric rod actuator replace a hydraulic cylinder?
Often, yes, especially where force needs are moderate and precise positioning, cleanliness or energy savings matter. Electric rod actuators with roller screws reach high forces, but extreme forces in a small envelope still favour hydraulics. Compare peak and continuous force, duty, shock loads and space, and check the motor and drive sizing as well as the screw.
Further reading: How to size a linear actuator · Hydraulic to electric actuator · Linear actuators
Other rod actuator series
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Oriental Motor EAC Series electric linear cylinders (AZ): the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.