Stepper drive
Trinamic (Analog Devices) TMCM-1211 (StepRocker) stepper drive
Single-axis stepper controller/driver board built on the TMC5160: 10–30 V, up to 5.7 A RMS, 256 microsteps, StealthChop, StallGuard and CoolStep, with USB, RS485 and step/direction.
Need this part, a replacement or a better-fit option? Our engineers help with selection, procurement, sourcing, competitive pricing and lead times.
Engineering support · Product sourcing · Procurement
Get pricing or a checked replacement
Need Trinamic (Analog Devices) parts, a replacement or another suitable option? Send your part number or describe the application. We’ll review the requirement and help with product selection, sourcing, pricing and lead times.
- Exact parts and engineer-checked alternatives
- Manufacturer-direct options where available
- Standard, modified and custom solutions
No obligation to buy. Have a datasheet, drawing or nameplate photo? Reply to your confirmation email to attach it.
Need help choosing? Build a specification →Need help choosing? Open the specification builder
Spec builder
Specify what you need instead of TMCM-1211 (StepRocker)
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Key specifications
| Voltage (max) | 30 V |
|---|---|
| Data / bus | USB, RS485, step/direction |
| Supply | 10–30 VDC |
| Axes | 1 |
| Current (max) | 5.7 A |
| Microsteps | 256 |
| Features | SixPoint ramp controller, StallGuard, CoolStep, StealthChop; TMCL firmware |
Summarised in our own words from Analog Devices, Inc.'s published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Status 'Production' on the ADI page.
Specify Motion is not affiliated with Analog Devices, Inc.. Trinamic (Analog Devices) and TMCM-1211 (StepRocker) are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Trinamic (Analog Devices) TMCM-1211 (StepRocker) replacement and alternative options
Use these supply-network options as a starting point for an engineering check. We can also help source the original Trinamic (Analog Devices) part. Published series figures do not establish an exact-model or drop-in replacement: confirm ratings, fit, interfaces and approvals for your application.
3-phase open-loop stepper drives for 3S motors, from 50 VDC to 240 VAC input and up to 11.7 A.
| Published maximum | TMCM-1211 (StepRocker) | Leadshine 3DM Series (3-phase) |
|---|---|---|
| Continuous current | 5.7 A | 11.7 A meets or exceeds |
| Axes | 1 | — |
Legacy digital pulse drives from small 30 VDC units up to 240 VAC mains-input drives for NEMA 34-52 motors.
| Published maximum | TMCM-1211 (StepRocker) | Leadshine DM-E / DMA / DM high-voltage… |
|---|---|---|
| Continuous current | 5.7 A | 8.2 A meets or exceeds |
| Axes | 1 | — |
Digital open-loop pulse/direction stepper drives from 1.5 A to 8.2 A with auto-tuning, anti-resonance and soft start.
| Published maximum | TMCM-1211 (StepRocker) | Leadshine EM-S Series (EM415S-EM882S, … |
|---|---|---|
| Continuous current | 5.7 A | 8.2 A meets or exceeds |
| Axes | 1 | — |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
Typical applications
What a stepper drive is
An open-loop stepper drive powers a stepper motor by switching current through its windings in sequence, usually using a chopper that regulates phase current to a set level. It receives step and direction pulses from a controller, and each pulse moves the motor by one step or microstep. Settings for current, microstepping and idle current are made by switches or software. Without position feedback, the drive assumes the motor follows each step.
When engineers choose a stepper drive
Choose an open-loop stepper drive for simple, low-cost positioning where loads are predictable and missed steps are unlikely, such as indexers, small axes and instruments. It is easy to set up with no tuning. The trade-offs are no stall detection, heat from constant current and resonance at some speeds. Where loads vary or a lost position would cause a fault, a closed-loop stepper drive or servo is safer.
How to specify the Trinamic (Analog Devices) TMCM-1211 (StepRocker)
Send these with your enquiry and an engineer can confirm the right TMCM-1211 (StepRocker) variant or an equivalent:
- Supply voltage (V DC or AC)
- Phase current range (A)
- Motor type: two-phase or three-phase
- Microstep settings
- Pulse input frequency and signal levels
- Idle current reduction
- Mounting and cooling
Common mistakes to avoid
- Supply voltage too low for the speed required
- Setting current above the motor rating
- Ignoring mid-speed resonance
- Mismatching pulse signal levels with the controller
Trinamic (Analog Devices) TMCM-1211 (StepRocker): frequently asked questions
Can you help replace Trinamic (Analog Devices) TMCM-1211 (StepRocker) or source the original?
Send the full model code, quantity and required date. Our engineers can check original-part availability and assess suitable alternatives, including Motion Control Products options where appropriate. We confirm compatibility and any changes needed before recommending a replacement.
What is the Trinamic (Analog Devices) TMCM-1211 (StepRocker)?
Single-axis stepper controller/driver board built on the TMC5160: 10–30 V, up to 5.7 A RMS, 256 microsteps, StealthChop, StallGuard and CoolStep, with USB, RS485 and step/direction. Published series figures include voltage 30 V, axes 1, current 5.7 A. It is made by Analog Devices, Inc.; Specify Motion can help source it or propose an equivalent.
Who makes the Trinamic (Analog Devices) TMCM-1211 (StepRocker)?
The Trinamic (Analog Devices) TMCM-1211 (StepRocker) is made by Trinamic (Analog Devices) (Analog Devices, Inc.) and is listed here for engineers comparing options. Specify Motion is not affiliated with Analog Devices, Inc.; brand names are used only to identify the product.
What is the voltage of the Trinamic (Analog Devices) TMCM-1211 (StepRocker)?
The published series maximum voltage is 30 V. Individual models and sizes in the TMCM-1211 (StepRocker) range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Trinamic (Analog Devices) TMCM-1211 (StepRocker)?
We can assess suitable replacement options. On published figures, Leadshine 3DM Series (3-phase) and Leadshine DM-E / DMA / DM high-voltage Series are options to assess from our supply network. An engineer confirms the fit against your application before recommending anything.
How does supply voltage affect stepper performance?
Higher supply voltage lets current rise faster in the motor windings, so torque is maintained to higher speeds. A common rule of thumb is to keep the supply within the motor and drive limits, often several times the motor's rated voltage. Check the drive's maximum voltage and the motor's insulation rating.
What is idle current reduction?
Idle current reduction lowers motor current automatically when the motor is stationary, reducing heat while still holding position with reduced torque. It is useful for steppers that spend time at standstill. Check that the reduced holding torque is enough for the load.
Further reading: How to select a stepper drive · How to select a stepper motor · Servo drives
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Trinamic (Analog Devices) TMCM-1211 (StepRocker): the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.