Rod actuator
LINAK LA76 rod actuator
Brushless DC (BLDC) TECHLINE rod actuator for extended service life: up to 6,800 N, up to 142 mm/s and 100 to 1,200 mm stroke, life-tested to at least 200,000 cycles at maximum load.
Need this part, a replacement or a better-fit option? Our engineers help with selection, procurement, sourcing, competitive pricing and lead times.
Engineering support · Product sourcing · Procurement
Get pricing or a checked replacement
Need LINAK parts, a replacement or another suitable option? Send your part number or describe the application. We’ll review the requirement and help with product selection, sourcing, pricing and lead times.
- Exact parts and engineer-checked alternatives
- Manufacturer-direct options where available
- Standard, modified and custom solutions
No obligation to buy. Have a datasheet, drawing or nameplate photo? Reply to your confirmation email to attach it.
Need help choosing? Build a specification →Need help choosing? Open the specification builder
Spec builder
Specify what you need instead of LA76
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Key specifications
| Voltage (max) | 48 V |
|---|---|
| Ingress protection | IP66 dynamic / IP69K static |
| Data / bus | CANopen, CAN SAE J1939, IO-Link, LIN bus, Modbus RTU, EtherNet/IP, Modbus TCP/IP, PROFINET (IC integrated controller options); LINAK I/O |
| Force (max) | 6,800 N |
| Stroke (max) | 1,200 mm |
| Linear speed (max) | 142 mm/s |
| Supply | 24 or 48 V DC |
| Motor | brushless DC |
| Life | minimum 200,000 cycles at max load and max duty cycle (LINAK test) |
Summarised in our own words from LINAK A/S's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1 · Source 2
Specify Motion is not affiliated with LINAK A/S. LINAK and LA76 are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
LINAK LA76 replacement and alternative options
Use these supply-network options as a starting point for an engineering check. We can also help source the original LINAK part. Published series figures do not establish an exact-model or drop-in replacement: confirm ratings, fit, interfaces and approvals for your application.
General-purpose electric rod actuator in six sizes with solid, bronze or ball screws and inline or reverse-parallel motor mounting; a broad pneumatic/hydraulic replacement workhorse.
| Published maximum | LA76 | RSA-ST (standard thrust) |
|---|---|---|
| Force | 6,800 N | 17,917 N meets or exceeds |
| Stroke | 1,200 mm | 1,524 mm meets or exceeds |
| Speed | 142 mm/s | 3,124 mm/s meets or exceeds |
Screw-driven rodless actuator with recirculating ball-bearing guidance integral to the extrusion, so it carries loads up to 35.6 kN (with carrier options) without external guides.
| Published maximum | LA76 | B3S Screw-Drive Rodless |
|---|---|---|
| Force | 6,800 N | 12,010 N meets or exceeds |
| Stroke | 1,200 mm | 4,547 mm meets or exceeds |
| Speed | 142 mm/s | 1,524 mm/s meets or exceeds |
Heavy-duty version of the RSA rod actuator with roller-screw options, matched angular-contact bearings and larger motor mounts, reaching 58 kN on size 64.
| Published maximum | LA76 | RSA-HT (high thrust) |
|---|---|---|
| Force | 6,800 N | 58,000 N meets or exceeds |
| Stroke | 1,200 mm | 1,524 mm meets or exceeds |
| Speed | 142 mm/s | 3,124 mm/s meets or exceeds |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
Typical applications
What a rod actuator is
A rod actuator, sometimes called an electric cylinder, converts motor rotation into linear thrust through a screw and nut inside a tube, pushing a rod in and out like a pneumatic or hydraulic cylinder. The screw is usually a ball screw for efficiency, a roller screw for heavy loads or a lead screw for low cost. The rod is guided by bearings in the tube and an anti-rotation feature, and the motor is mounted inline or folded alongside through a belt or gear stage.
When engineers choose a rod actuator
Choose a rod actuator when the load is guided externally and needs pushing or pulling with controlled force, speed and position, typically to replace a pneumatic or hydraulic cylinder. It brings programmable positions, force control and energy savings. The trade-offs are side load and cost: the rod is not meant to carry significant radial load, and peak force for its size is lower than hydraulics. If the load needs carrying and guiding along the stroke, a rodless actuator or stage is usually better.
How to specify the LINAK LA76
Send these with your enquiry and an engineer can confirm the right LA76 variant or an equivalent:
- Force: peak and continuous or RMS (N)
- Stroke (mm) and retracted length limits
- Speed and acceleration (mm/s, m/s²)
- Duty cycle or full motion profile
- Positioning repeatability (mm)
- Side load and mounting arrangement: trunnion, clevis or flange
- Motor and feedback preference, and environment (IP code, °C)
Common mistakes to avoid
- Sizing on peak force alone instead of RMS force over the cycle
- Rigidly mounting both ends so misalignment puts side load on the rod
- Ignoring critical speed and column buckling on long strokes
- Forgetting that a ball screw back-drives, so vertical loads need a brake
LINAK LA76: frequently asked questions
Can you help replace LINAK LA76 or source the original?
Send the full model code, quantity and required date. Our engineers can check original-part availability and assess suitable alternatives, including Motion Control Products options where appropriate. We confirm compatibility and any changes needed before recommending a replacement.
What is the LINAK LA76?
Brushless DC (BLDC) TECHLINE rod actuator for extended service life: up to 6,800 N, up to 142 mm/s and 100 to 1,200 mm stroke, life-tested to at least 200,000 cycles at maximum load. Published series figures include voltage 48 V, force 6,800 N, stroke 1,200 mm, linear speed 142 mm/s. It is made by LINAK A/S; Specify Motion can help source it or propose an equivalent.
Who makes the LINAK LA76?
The LINAK LA76 is made by LINAK (LINAK A/S) and is listed here for engineers comparing options. Specify Motion is not affiliated with LINAK A/S; brand names are used only to identify the product.
What is the voltage of the LINAK LA76?
The published series maximum voltage is 48 V. Individual models and sizes in the LA76 range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the LINAK LA76?
We can assess suitable replacement options. On published figures, Tolomatic RSA-ST (standard thrust) and Tolomatic B3S Screw-Drive Rodless are options to assess from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the difference between a rod actuator and a rodless actuator?
A rod actuator pushes and pulls a rod extending from its body, so it suits loads that are guided by the machine, much like a cylinder. A rodless actuator moves a carriage along the body and carries the load itself, which handles moment loads and long strokes within the actuator's own length. Pick rod for thrust and rodless for carrying.
Can an electric rod actuator replace a hydraulic cylinder?
Often, yes, especially where force needs are moderate and precise positioning, cleanliness or energy savings matter. Electric rod actuators with roller screws reach high forces, but extreme forces in a small envelope still favour hydraulics. Compare peak and continuous force, duty, shock loads and space, and check the motor and drive sizing as well as the screw.
Further reading: How to size a linear actuator · Hydraulic to electric actuator · Linear actuators
Other rod actuator series
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the LINAK LA76: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.