CubeMars

CubeMars contact details

CubeMars headquarters

Room 301, Building 33, JiaHai Industrial Park
No. 2799 Tianxiang Avenue, Gaoxin District
Nanchang, Jiangxi Province
China

Telephone +86 137 5564 9079

Email info@cubemars.com

Website cubemars.com

Show CubeMars headquarters on the map Open in Google Maps →

Contact details as published by Nanchang Kude Intelligent Technology Co., Ltd. (wholly owned subsidiary of Nanchang Sanrui Intelligent Technology Co., Ltd.), checked 2026-10-30. Specify Motion is not affiliated with Nanchang Kude Intelligent Technology Co., Ltd. (wholly owned subsidiary of Nanchang Sanrui Intelligent Technology Co., Ltd.).

CubeMars product lines

Who CubeMars is

CubeMars is a Chinese brand of robot joint actuators and frameless torque motors. Its best-known products are the AK Series, compact actuators that combine a brushless motor, planetary gear stage, driver electronics and encoders in one housing. They have become a common sight in university legged robots, exoskeletons and research humanoids, because a builder can bolt one on, connect a CAN bus and a 24 or 48 V supply, and have a torque-controlled joint.

For OEM engineers, CubeMars sits at the accessible end of the joint actuator market: published prices, small quantities available online, and lightweight parts aimed at dynamic, back-drivable joints rather than heavy industrial duty.

History and ownership

The company behind the brand is Nanchang Kude Intelligent Technology Co., Ltd. Its about page describes Kude as a wholly owned subsidiary of Nanchang Sanrui Intelligent Technology Co., Ltd. and calls CubeMars a brand under Sanrui Intelligent. The milestones published are:

• 2009: Sanrui Intelligent established.
• 2018: the CubeMars brand officially established, building on what the company calls 17 years of motor technology.
• 2026: a Sanrui IPO is listed on the about page.

CubeMars cites an annual output of 6 million units across the group, in-house R&D, manufacturing and service, and “international certifications” without naming them. It does not publish a headcount.

Product portfolio

Joint actuators

• The AK Series runs from the 190 g AK40-10 (4.1 Nm peak) to the AK80-64 (48 Nm rated, 120 Nm peak, series maximum, 64:1). The widely used AK10-9 V3.0 gives 18 Nm rated and 53 Nm peak at 48 V through a 9:1 planetary stage, with 21-bit and 15-bit magnetic encoders and CAN control in servo or MIT mode. CubeMars publishes a backlash of 0.18° for the AK80-64.
• The AKE Series is the quasi-direct-drive range with low ratios (8:1 on the AKE90-8), from the 140 g AKE40-6 to the AKE90-8 at 55 Nm rated and 170 Nm peak at 48 V.

Quasi-direct-drive (QDD) actuators use a large-diameter motor and a low gear ratio so the joint stays back-drivable and can sense contact through motor current. The trade-off against a high-ratio harmonic actuator is lower continuous torque density and more output backlash. Our guide to harmonic vs planetary vs cycloidal gearing covers that choice.

Frameless torque motors

• The RI Series are frameless inrunner motors from 25 mm (RI20, 72 mNm peak) to 104 mm diameter (RI100, 4.95 Nm peak).
• The RO Series are frameless outrunners from the RO40 Lite (0.6 Nm peak) to the 113.5 mm RO100 (12 Nm peak).

These let a designer build a custom joint around their own bearings, gear stage and encoder. See frameless motor sizing for robot joints and the frameless torque motors hub.

Technologies

The AK and AKE products are built around field-oriented control in an integrated driver, dual encoders on newer versions (one on the motor, one on the output), and CAN bus with a choice of a position/velocity servo mode or the impedance-style “MIT mode” popular in legged robotics. Encoder resolution, rated versus peak torque and thermal limits differ a lot between models, so it is worth comparing each product page rather than the series headline.

Industries served

CubeMars names legged and foot-type robots, exoskeletons, AGVs, collaborative robot arms, humanoid robots and industrial automation as its target applications. Most published use is in research, education and early-stage product development. See robotics and cobots for how joint actuators are specified for production machines.

AK or AKE: a quick way to choose

Start from the joint’s continuous torque, not the peak. A walking robot’s knee spends most of its time holding body weight, so the rated (continuous) figure and the motor’s temperature rise decide the size; the peak figure only has to cover jumps, impacts and short accelerations. Where CubeMars publishes both, peak is roughly three times rated (for example 18 Nm and 53 Nm on the AK10-9 V3.0), so a design sized on peak alone will overheat. Choose a higher ratio such as the AK80-64 when the joint needs holding torque at low speed and back-drivability matters less; choose an 8:1 AKE or AK model when the joint must be fast, transparent to external forces and able to absorb impacts. Check the published voltage, bus and control mode against your controller before committing.

Global and UK presence

CubeMars sells directly from Nanchang and through its online shop. Its contact page lists no overseas offices or distributors, and there is no UK office. UK engineers should allow for import lead times, CE/UKCA documentation checks and the level of technical support needed when moving from prototype to production.

What to send when specifying a joint actuator

Give the continuous and peak torque at the joint, speed, duty cycle, supply voltage, the bus your controller uses (CAN, EtherCAT), required encoder resolution and whether output-side absolute position is needed, mass and envelope limits, backlash tolerance, and environment.

Specify Motion is independent of CubeMars. Our engineers can help source CubeMars products or propose equivalents from our supply network on published figures; see find a replacement or the servo and stepper motors hub.

CubeMars history: key dates

1. 2009Parent company Nanchang Sanrui Intelligent Technology established
2. 2018CubeMars brand officially established
3. 2026Sanrui Intelligent IPO listed on the CubeMars about page

CubeMars harmonic actuators

Integrated robot joint actuator

AK Series

Planetary-geared robot joint actuators with built-in driver and magnetic encoders, from the 190 g AK40-10 to the AK80-64 (series maximum 120 Nm peak); the AK10-9 V3.0 gives 18 Nm rated and 53 Nm peak at 48 V.

Integrated robot joint actuator

AKE Series

Quasi-direct-drive joint actuators with a low-ratio planetary stage, from the 140 g AKE40-6 (5.5 Nm peak) to the AKE90-8 at 55 Nm rated and 170 Nm peak (series maximum) at 48 V.

CubeMars direct-drive and torque motors

Frameless torque motor

RI Series

Frameless inrunner torque motor kits from 25 mm (RI20, 72 mNm peak) to 104 mm diameter (RI100, 4.95 Nm peak, series maximum) for building custom joints.

Frameless torque motor

RO Series

Frameless outrunner torque motors from the RO40 Lite (0.6 Nm peak) to the 113.5 mm RO100 (12 Nm peak, series maximum).

Frequently asked questions

What is the CubeMars website?

CubeMars's official website is cubemars.com. It lists the AK and AKE robotic actuators, RI and RO frameless torque motors, drivers and accessories with prices and data, plus an about page describing the company and a contact page with the Nanchang headquarters address, phone and email.

What is CubeMars's phone number and email?

CubeMars publishes +86 137 5564 9079 as its telephone and WeChat contact, with info@cubemars.com as its email address. Its working hours are Monday to Friday, 09:00 to 18:00 China time (UTC+8).

Where is CubeMars based?

CubeMars's headquarters is at Room 301, Building 33, JiaHai Industrial Park, No. 2799 Tianxiang Avenue, Gaoxin District, Nanchang, Jiangxi Province, China. The contact page lists no overseas offices.

Who owns CubeMars?

CubeMars is a brand of Nanchang Kude Intelligent Technology Co., Ltd., which its about page describes as a wholly owned subsidiary of Nanchang Sanrui Intelligent Technology Co., Ltd. Sanrui was established in 2009, and the about page also lists a Sanrui IPO in 2026.

Does CubeMars have a UK distributor?

The CubeMars contact page lists no UK office or distributor; it sells directly from China and through its online store. Specify Motion is independent of CubeMars and can help source its actuators or propose equivalents with industrial support.

What does CubeMars make?

CubeMars makes integrated robot joint actuators (the AK Series with planetary gearing and the AKE quasi-direct-drive series), RI inrunner and RO outrunner frameless torque motors, driver boards and accessories. Its actuators are used in legged robots, exoskeletons, humanoids, AGVs and robot arms.

Sources

1. CubeMars: About us
2. CubeMars: Contact us
3. CubeMars: Home page
4. CubeMars: AK Series robotic actuators
5. CubeMars: AK10-9 V3.0 KV60
6. CubeMars: AK80-64 KV80
7. CubeMars: AKE Series
8. CubeMars: AKE90-8 KV35
9. CubeMars: RI Series frameless inrunner torque motors
10. CubeMars: RO Series frameless outrunner torque motors

Figures are summarised from the sources above and from manufacturers' published data on the date shown. Always confirm against the current datasheet for your exact part.