Magnetic rotary encoder
Baumer MAGRES EAM580 magnetic rotary encoder
58 mm magnetic multi-turn absolute encoder; the SSI blind-hollow-shaft version gives 13-bit single-turn and 12-bit multi-turn (25 bits), ±0.15° accuracy, 6,000 rpm and -40 to +85 °C.
Key specifications
| Speed (max) | 6,000 rpm |
|---|---|
| Bore (max) | 12 mm |
| Ingress protection | IP65 (IP67 variants) |
| Temperature | -40–85 °C |
| Data / bus | SSI, EtherNet/IP |
| Supply | 4.5–30 V DC |
| Resolution (max) | 25 bit |
| Accuracy | ±0.15° at 20 ±15 °C; ±0.25° over -40 to +85 °C |
| Resolution | 13 bit single-turn + 12 bit multi-turn (SSI version read) |
| Housing | 58 |
Summarised in our own words from Baumer Group's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Only one product page could be read (Baumer site refused most fetches). EtherNet/IP version exists per Baumer product page titles (not read).
Specify Motion is not affiliated with Baumer Group. Baumer and MAGRES EAM580 are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Typical applications
Alternatives that meet or exceed these figures
Engineers often come to us with a Baumer part number and leave with an alternative that is easier to source, quicker to deliver or a better fit for the machine. These 3 series from our supply network are the closest match on published figures.
Incremental magnetic head in plastic or die-cast housing, RS422/TTL output. Works on linear and rotary scales.
View IKS9 / IKS9.1 →Compact incremental head with wide -40 to +125 C range; IKP11 is the open IP00 version. Works on linear and rotary scales.
View IKS11 / IKP11 →Incremental magnetic head with analogue sin/cos output. Works on linear and rotary scales.
View IKS15 / IKS15.1 →Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
What a magnetic rotary encoder is
A magnetic rotary encoder measures angle by sensing the field of a magnet with Hall-effect or magnetoresistive sensors. On-axis designs place a diametrically magnetised magnet on the shaft end above a sensor chip; off-axis designs read a multi-pole magnetic ring around a hollow shaft. Signal processing turns the field into absolute or incremental position. Because there is no optical path, magnetic encoders tolerate dust, oil, moisture and vibration, typically with moderate resolution and accuracy at low cost.
When engineers choose a magnetic rotary encoder
Choose a magnetic rotary encoder for robust, compact feedback in harsh or cost-sensitive applications, such as motors, AGVs, robotics, agricultural and mobile machinery. Off-axis rings suit hollow joints. The trade-offs are accuracy and magnetic interference: accuracy is typically lower than optical, and strong stray fields from brakes or motors can affect the reading. For high precision, choose optical. Consider shielding and mounting tolerances carefully.
How to specify the Baumer MAGRES EAM580
Send these with your enquiry and an engineer can confirm the right MAGRES EAM580 variant or an equivalent:
- Resolution (bits or counts)
- Accuracy (degrees or arcmin)
- Absolute or incremental output
- On-axis or off-axis ring mounting
- Interface: SSI, BiSS, SPI, PWM or analogue
- Mounting tolerances: gap and runout (mm)
- Environment and IP code
Common mistakes to avoid
- Mounting near brakes or motor magnets without shielding
- Exceeding the allowed air gap or runout
- Expecting optical accuracy from a magnetic encoder
- Overlooking calibration after installation
Baumer MAGRES EAM580: frequently asked questions
What is the Baumer MAGRES EAM580?
58 mm magnetic multi-turn absolute encoder; the SSI blind-hollow-shaft version gives 13-bit single-turn and 12-bit multi-turn (25 bits), ±0.15° accuracy, 6,000 rpm and -40 to +85 °C. Published series figures include speed 6,000 rpm, bore 12 mm, temperature -40 °C, temperature 85 °C. It is made by Baumer Group; Specify Motion can help source it or propose an equivalent.
Who makes the Baumer MAGRES EAM580?
The Baumer MAGRES EAM580 is made by Baumer (Baumer Group) and is listed here for engineers comparing options. Specify Motion is not affiliated with Baumer Group; brand names are used only to identify the product.
What is the speed of the Baumer MAGRES EAM580?
The published series maximum speed is 6,000 rpm. Individual models and sizes in the MAGRES EAM580 range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Baumer MAGRES EAM580?
Yes. On published figures, Bogen IKS9 / IKS9.1 and Bogen IKS11 / IKP11 are the closest match from our supply network. An engineer confirms the fit against your application before recommending anything.
Are magnetic encoders as accurate as optical encoders?
Typically not. Magnetic encoders tolerate contamination and vibration well but usually have lower accuracy and resolution than optical encoders of similar size. Self-calibration and good mounting can improve results. For high-precision positioning and metrology, optical encoders remain the usual choice, while magnetic types win on robustness and cost.
What is the difference between on-axis and off-axis magnetic encoders?
On-axis encoders read a single magnet on the end of a shaft, which is simple and compact. Off-axis encoders read a magnetic ring around a shaft, which leaves the centre free for hollow shafts or cables. Off-axis designs are more sensitive to mounting tolerances.
Further reading: Magnetic vs capacitive vs optical encoders · How to select an encoder · Encoders and feedback
Other magnetic rotary encoder series
Spec builder
Specify what you need instead of MAGRES EAM580
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Baumer MAGRES EAM580: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.